American-diagnostic-corporation-adc Diagnostix 972 Assembly Manuel d'utilisateur télécharger pdf

DIAGNOSTIX

™

972

• Assembly Instructions

• Schematics

• Parts List

MAINTENANCE

1. With base on its side connect upright outer

sleeve to base using large (6mm) allen nut

and lock washer as shown. Tighten with

large (6mm) allen key provided. Note:

Tighten hex nut securely by applying as

much force to allen key as possible.

2. Turn base upright and slide stainless steel

inner tube inside outer sleeve with open

end up.

3. Loosen (3mm) allen nut on collar of cuff

storage basket with small (3mm) allen key

provided. Place cuff storage basket atop

stainless steel inner tube making sure the

tube goes completely inside collar and

tighten allen nut with key.

4. Attach the main unit to the cuff storage

basket and secure with large (6mm) allen

nut and washers as shown.

5. Adjust height of mercury unit by

loosening adjusting screw and

raising or lowering inner tube until mercury

column is at desired height. Tighten

adjusting screw by hand.

6. Carefully remove red connector cap

covering reservoir connector at rear of

unit. Attach the coiled tubing to reservoir

connector on the back of main unit. (Note

the coiled tubing may be difficult to

connect - moisten with soapy water if

necessary). Connect coiled tubing to

inflation system. Refer to booklet entitled

DIAGNOSTIX 972

™

MERCURIAL BLOOD

PRESSURE INSTRUMENT for

instructions on operating the unit.

To Lock Mercury Within the Reservoir: Tilt the entire unit back

45° towards the reservoir to permit mercury to flow out of

cartridge tube and into reservoir. When cartridge tube is

completely emptied of ALL mercury (and while it is still tilted

45°), move locking lever to the right “OFF”. Mercury should be

locked within the reservoir during maintenance or transport. To

release mercury, move lever to “ON” position. If necessary, tilt

unit towards tube to allow mercury to flow out of reservoir.

Lift on the spring loaded EZ-Tube

™

mechanism

located at the top of the instrument. Tilt

instrument forward to free tube. If necessary

use a small flathead screwdriver to help

dislodge the top of the tube. To replace tube,

lift EZ-Tube

™

mechanism and insert base of

tube into main unit, being sure graduation

marks face out. Next, position top of tube and

release EZ-Tube

™

mechanism.

®

To Register Your Product, visit us at www.adctoday.com and follow the links

HOW TO ASSEMBLE

Included Tools

Tighten hardware as securely as

possible. (Note: To prevent

loosening, hardware must be

tightened securely and

periodically checked).

Slide inner tube inside outer tube.

Attach main unit to cuff

storage basket.

Insert pole to bottom of cuff

basket and tighten allen bolt on

side of the cuff storage basket

with small allen key.

6mm 3mm

ADC

55 Commerce Drive

Hauppauge, NY 11788

ADC (UK) Ltd.

Unit 6, PO14 1TH

United Kingdom

tel: 631-273-9600, 1-800-232-2670

fax: 631-273-9659

www.adctoday.com

email: info@adctoday.com

EC REP

IB p/n 9357A-00 - rev 5 Printed in U.S.A.

1 2

DIAGNOSTIX 1
SCHEMATIC PARTS LIST 2

Résumé du contenu

Page 1 - DIAGNOSTIX

DIAGNOSTIX™972• Assembly Instructions• Schematics• Parts ListMAINTENANCE1. With base on its side connect upright outersleeve to base using large (6mm)

Page 2 - SCHEMATIC PARTS LIST

SCHEMATIC PARTS LIST2236232425262728293031M32M33343518192021789101112Ref # Item # Description13 952-109 Reservoir Connector14 952-110 Cotton Filter15

Commentaires sur ces manuels

Pas de commentaire

American-diagnostic-corporation-adc Diagnostix 972 Assembly Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Instruments de mesure American-diagnostic-corporation-adc Diagnostix 972 Assembly. American Diagnostic Corporation (ADC) Diagnostix 972 Assembly User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de mesure American-diagnostic-corporation-adc Diagnostix 972 Assembly